Unistrut P3922 EG Splice Plate Fitting - P3922-EG (Options: Electro-Galvanized)

Sku:

P3922-EG

UOM: EA

Product Details

Splice Fitting


Unistrut Buffalo is a division of Eberl Iron Works, Inc.

 

     

More Information
SKU P3922-EG
EAN 0786364392219
Pack Size Each
UOM EA
UPC 786364392219
Brand Unistrut
Finish Electro-Galvanized

STANDARD DIMENSIONS

Standard Dimensions for 1-5/8" (41.3 mm) width series channel (Unless otherwise specified in Unistrut General Engineering Catalog):

Hole Diameter: 9/16" (14.3 mm)

Hole Spacing - From End: 13/16" (20.6 mm)

Hole Spacing - On Center: 1-7/8" (47.6 mm)

Width: 1-5/8" (41.3 mm)

Thickness: 1/4" (6.4 mm) with steel meeting or exceeding ASTM A1011 SS GR 33, or 0.220" (5.6mm) with steel meeting or exceeding ASTM A1011 HSLAS GR 45

Note: When used for mechanical supports, load capacities of brackets, fittings and other supporting elements should be in compliance with the American Standard Code for Pressure Piping. Clamps are designed to be used with W, M, S & HP Shape beams, Standard C & Misc. MC Channels, Angles & Structural Tees. Clamps must be used in pairs where indicated. For beam clamps with HG finish, standard hardware is EG finish. For optional stainless steel hardware, please contact the factory for availability.

MATERIAL

Unistrut fittings, unless noted, are made from hot-rolled, pickled and oiled steel plates, strip, bar or coil, and conform to one or more of the following specifications:

ASTM A575, A576, A635, A1011 SS GR 33, A1011 HSLAS GR 45 or A36. The fitting steel also meets or exceeds the physical requirements of ASTM A1011 SS GR 33.

Maple cable saddles, cable clamps and bus bar clamps are made from kiln-dry maple treated with paraffin to a depth of 1⁄16" (1.6mm). Special sizes of clamps can be fabricated upon request. Cable saddles are fiberglassreinforced polyester.

CHANNEL RACEWAYS

The Unistrut Metal Framing System includes an exclusive combination of channel, fittings and hardware listed under new UL classification 5B. This classification covers strut-type channel raceways and fittings for use in accordance with Article 384 of the National Electrical Code, NFPA 70. Included are metal strut-type channel raceways at least .071 inch (1.81mm) thick and metal or non-metal closure strips at least .040 inch (1.02mm) thick.

The Unistrut system requires no welding, drilling or other complex fabrication techniques. This means faster, easier solutions for virtually any electrical support problem.

Unistrut channel offers structural and spanning capabilities not available with conventional surface raceway products and is available in continuous lengths of up to 20 feet. Just as important, it is part of an integrated system that can be used for raceways, trapeze hangers, cable-tray supports, lighting grids, fluorescent-fixture supports and countless other electrical applications.

CHANNEL COMPATABILITY

All of the electrical components in this section are intended for use with any of the 15⁄8" wide channel. They are not intended for use with 11⁄4" or 13⁄16" framing systems.

FINISHES

Components listed in this section are available in:

  • Electro-galvanized (EG), conforming to ASTM B633 Type III SC1
  • Hot-dipped galvanized (HG), conforming to ASTM A123 or A153
  • Green Powder Coat (GR), conforming to commercial standards for Powder Coating
  • Plain (PL)

*** Perma Green finish is a commercial grade finish, and as such scuffs and scratch marks are to be expected. If a flawless finish is desired, it is recommended to apply a matching touch up paint ***

Note: Many Unistrut Metal Framing components, when used with appropriate closures, are UL® listed, and CSA approved.

DESIGN LOAD

Design load data, where shown, is based on the ultimate strength of the connection with a safety factor of 2.5, unless otherwise noted.

DIMENSIONS

Imperial dimensions are illustrated in inches. Metric dimensions are shown in parenthesis or as noted. Unless noted, all metric dimensions are in millimeters and rounded to one decimal place.

LISTINGS

File Number Product Type
UL File No. - E19459 Channel & Closure Strips
UL File No. - E25629 Fittings
CSA File No. - 013669 All Products

 

Get your free copy of the Unistrut No. 17 General Engineering Catalog

Save paper! Download the most up to date version of Unistrut's General Engineering Catalog, right here, in digital format.

  • Unistrut Part Numbers
  • Product specifications
  • Engineering Data
  • Load Tables
  • Product Finish Information,
  • and more!
Unistrut-Catalog-17

*Please note, catalog is in PDF format. You must have Adobe Reader (a FREE and trusted program) installed, to view. If you do not already have Adobe Reader installed, you may download it from Adobe's website. *Download times may vary, file is large.*

Save paper! Download the most up to date version of Unistrut's General Engineering Catalog, right here, in digital format.

Write Your Own Review
You're reviewing:Unistrut P3922 EG Splice Plate Fitting - P3922-EG (Options: Electro-Galvanized)